Site Search
Latest Topics
You are here:
[AIX]How to Displaying program output and copying to a file (tee command)
The tee command, used with a pipe, reads standard input, then writes the output of a program to standard output and simultaneously copies it into the specified file or files. Use the tee command to view your output immediately and at the same time, store it for future use.
[AIX]How to find out what kernel mode AIX is running at?
/unix is a symbolic link to the booted kernel. To find out what kernel mode is running, enter ls -l /unix and see what file /unix it links to. The following are the three possible outputs from the ls -l /unix command and their corresponding kernels:
More Articles...
- [AIX] How to change between kernel modes in AIX?
- [AIX] How to create a file system?
- [AIX] How to change the size of a file system?
- [AIX] How to mount a CD/DVD?
- [AIX]How to defragment a file system?
- [AIX] How to remove a file system?
- [AIX] How to increase /reduce a paging space?
- [AIX] How to create a logical volume?
- [AIX] How to increase the size of a logical volume?
- [SAN Storage] Multipath Software for P5 VIO
- [AIX]Why there are ghost LUNs(LUNz) presented to host?
- [AIX]Difference between AIX Maintenance Level(ML), Technology Level(TL) and Service Pack
- [AIX] How to match AIX Hdisk number to Clariion Array LUN number?
- [AIX.DMX]How to configure AIX devices after symm(device) configuration change?
- [AIX]How to setup to enable syslog in AIX?
- [IBM SVC]IBM SVC Restrictions - 5.1.x
- [IBM SVC]IBM SVC Restrictions - 4.3.x
- [SAN Storage] Complete Organization WWN Registration List - Part 4
- [SAN Storage] Complete Organization WWN Registration List - Part 3
- [SAN Storage] Complete Organization WWN Registration List - Part 2
- [SAN Storage] Complete Organization WWN Registration List - Part 1
- [SAN Storage] UNIX/LINUX OS Disk Management
- [IBM Storage] Identify IBM Storage by WWPN
- [IBM] Default IBM Hardware Access ID and Password
- [IBM DS] Loops and switches on the DS6000 and DS8000
- [IBM DS] DS8000 Terms and Concepts
- [IBM TPC] HW/SW Requirement for Implement TPC for Replication
- [IBM SVC] How to run performance review using SVC CLI Scripts
- [IBM Storage] SDD/SDDPCM multipath limitations and recommendations for AIX
- [SAN HPUX]How to setup host connectivity for HPUX 11iV3 that connects to Clariion without Powerpath
- [SAN-HPUX] How to find out the CLARiiON LUN number based on the HPUX host device output?
- [Brocade]How can I tell if a Brocade switch has Core PID set?
- [Brocade]Upgrade Firmware on Silkworm switchs
- [Brocade] How to save the supportshow output?
- [Brocade] Understand Fibre Channel logins
- [Brocade]Gracefully shut down Brocade switches and directors
- [Brocade] SAN Zoning - Guideline and considerations
- [Brocade] SAN Zoning - CLI
- [Brocade] Default HP HW Access ID and Password
- [Brocade]How to find out the model Brocade Switch from a Switchshow/Supportshow?
- [Brocade] Brocade CLI Command
- [Brocade] Setup console session brocade switch(serial connect)
- [Brocade] Troubleshooting - Switch Port shown wrong mode
- [Brocade] Troubleshooting - Marginal Links
- [Brocade] Default Brocade Access ID and Password
- [Brocade] SAN Zoning - Zoning Architecture
- [NETAPPS]How to check aggregates status using CLI to find out the spare disks?
- [NETAPP]How to find out aggregates total space and available space ?
- [NETAPP]How to Zero disk spare ?
- [NETAPP] How to Add more disk to existing Aggregation ?
Page 1 of 47
Login
Custom Search
Copyright 2010(c), Innovite Consulting Inc.( Devision of SynergyGear Tech)